We independently review everything we recommend. When you buy through our links, we may earn a commission. Learn more›

Home Audio Cable Checklist: HDMI, Optical, RCA, Speaker

Most systems need HDMI, speaker wire, a subwoofer cable and power. Match the cable to the job and skip premium prices where a certified basic cable works.

A typical home theater needs HDMI cables for video and audio, speaker wire for each passive speaker, one subwoofer cable, power cords, and sometimes Ethernet, optical or coaxial digital cables. Buy the correct type and length for each job, choose certified cables where a standard applies, and skip premium prices where a plain cable does the same work.

How to use this list

Walk through your equipment one device at a time and write down what connects to what. This prevents the common mistake of buying the wrong cable or too many of them. Our guide on how many HDMI inputs a receiver needs gives a worksheet that helps with the video side.

Use this quick method to build a shopping list. First, list every device with a power cord. Second, draw a line for every connection between two devices, and label it video, audio, network, or power. Third, measure each line along the path the cable will really take, adding a few inches of slack at each end. Fourth, check the ports on both ends, because a cable is only useful if both ends match. Finally, mark which lines carry high bandwidth video and which carry audio only, since that decides which cables need a certification label.

Keep this page open when you shop, and tick each item off as the cable arrives. Cables that arrive and do not fit are the most common reason for a second order, so verify the port types before you pay.

Device-by-Device Cable Checklist

AV receiver

  • HDMI inputs: one cable for each source, such as a streaming box, console or disc player.
  • HDMI output to the TV: one cable, and use the port that supports eARC if you want audio to return from the TV.
  • Speaker wire: one pair per passive speaker.
  • Subwoofer output: one cable from the receiver to the sub.
  • Ethernet: optional, for stable streaming and updates, if the receiver has a network port.
  • Power cord: usually included.
  • Antenna or other inputs: only if you use them.

TV

  • HDMI to the receiver, using the eARC capable port if your setup needs it.
  • Power cord, included.
  • Ethernet or Wi-Fi, depending on how you stream.
  • Optical output, which some TVs offer as an alternative to eARC for audio.

Sources

  • Streaming boxes, consoles and disc players each need an HDMI cable to the receiver or TV and a power cord. Ethernet is optional for network connected sources.
  • Turntables need a stereo cable and possibly a grounding wire, and a phono input or preamp on the receiver, as our guide on speakers for turntables discusses.

Speakers

Passive speakers need wire from the receiver. Choose a gauge for the run length and speaker impedance, as covered in our speaker wire gauge chart. For in-wall runs, use cable rated for in-wall use and follow your local code, as covered in our CL2 and CL3 explainer. If your speakers have binding posts, you may use bare wire or terminations, and our comparison of banana plugs and bare wire explains the trade-offs.

Powered speakers also need a power cord and a signal cable such as an analog cable or a wireless link.

Subwoofer

A powered subwoofer needs a single cable from the receiver’s subwoofer output to the sub’s line input, plus a power cord. A subwoofer cable is a shielded cable with a standard connector, and a standard well made one is sufficient for typical runs. Keep it away from power cords to reduce hum. If you use two subs, you need two cables and possibly a splitter, depending on outputs, as in our article on dual subwoofers.

Choosing the Right Cable Standard

Where HDMI standards matter

HDMI cables carry both picture and sound. For ordinary 4K video at normal frame rates, a certified high speed cable does the job. For higher bandwidth, such as 4K at high frame rates or 8K, use a cable certified for that bandwidth, and look for the certification label. Long runs may require special cables. Our checklist on HDMI passthrough gives the details.

A thick or expensive HDMI cable carries the same digital data as a cheaper certified one, as long as both meet the standard. You are paying for build quality, length or certification, and not for a better picture.

Cable length, bandwidth and what to do about long runs

Digital cables behave differently from analog ones. A cable that is too long or poorly made can drop out entirely instead of degrading gently. That is why long HDMI runs deserve care. For short runs inside a rack, almost any certified cable works. For runs across a room, choose a cable certified for the bandwidth you need, and consider active or fiber cables for the longest runs. Check the product page for the maximum length for the format you want, and buy a few inches more than you measure.

For speaker wire, longer runs call for a thicker gauge to avoid wasting power. Our speaker wire gauge guidance gives a method for matching gauge to length and impedance. For subwoofer cables, a long run is usually fine, but keep it away from power cables to avoid hum.

Ethernet, optical and coaxial

If your receiver and sources have network ports, a wired Ethernet connection is usually more reliable than Wi-Fi for streaming and updates. A standard network cable of an appropriate category does the job. Optical and coaxial digital cables carry audio only. They are useful for older devices or a TV that cannot use eARC. Check the maximum audio format that each supports, because optical connections cannot carry the highest quality surround formats. If you want the best audio from a TV, use eARC over HDMI.

Where to Spend and Where to Save

Where expensive cables are not needed

  • Digital cables, such as HDMI, optical and coaxial: the signal is digital, so it either arrives intact or fails, within the cable’s specification.
  • Short speaker wire runs: a reasonable gauge of ordinary copper wire is fine.
  • Subwoofer cables: a standard shielded cable is fine for typical runs.
  • Power cords: the included cords are generally adequate, and special cords rarely change anything audible. Check your manual before swapping.

Premium cables may offer better build, connectors and shielding, which can be valuable in difficult environments. They do not change sound in ways that standards based digital cables cannot.

When it is worth spending a little more

  • Long HDMI runs, which may need active cables or fiber.
  • In-wall installations that need the correct rating.
  • Locations with heavy electrical noise, where shielding helps.
  • Frequently moved gear, where a robust connector prevents failures.

Power, Labeling, and Spares

Surge protection and power

Plan outlets and power protection as well. See our guide on surge protectors versus power conditioners. Do not daisy chain power strips, and follow the ratings on each device.

Power cords and ground loops

The included power cords are usually adequate. If you hear hum or buzz, it may be a ground loop, which arises when equipment is connected to different grounding points. Try plugging everything into the same outlet strip, or check cable connections one at a time to find the cause. For persistent hum, consult a qualified electrician or technician. Do not defeat ground connections or cut ground pins, which is unsafe.

Labeling and spares

Label cables at both ends and keep a few spare lengths of HDMI and speaker wire. Leave slack at the back of the rack for service. Store the manuals and receipts in one place.

Building a spare kit

Keep a small box with one extra certified HDMI cable, a short length of speaker wire, a subwoofer cable and a spare Ethernet cable. When something fails, you can swap quickly and find out whether the cable was the problem. Label the box and note what each cable is for.

Verdict by System Size

  • Small systems: a handful of HDMI cables, speaker wire, a sub cable and power.
  • Larger systems: more HDMI, multiple speaker runs, and extra network cable.
  • In-wall installs: rated cable and a plan.

See our AV receivers section and home theater speakers pages for related guidance.

Frequently Asked Questions

What cables do I need for a home theater?

HDMI cables for video and audio, speaker wire for each passive speaker, one subwoofer cable, power cords, and sometimes Ethernet, optical, or coaxial cables. Walk through each device, write down what connects to what, and buy the correct type and length for each job.

Do expensive HDMI cables make a difference?

Not in picture quality. Digital cables carry the same data when they meet the standard, so a certified cable at the right bandwidth does the job. Spend extra only where length, an in-wall rating, shielding, or a robust connector solves a real problem.

What gauge speaker wire do I need?

It depends on the run length and speaker impedance. Longer runs and lower impedance speakers call for a thicker gauge, shown by a smaller AWG number. Check the speaker and receiver manuals, and use rated cable for any in-wall run.

Do I need a special subwoofer cable?

A standard shielded subwoofer cable with the correct connector is enough for typical runs. Connect the receiver’s subwoofer output to the sub’s line input, keep it away from power cords to reduce hum, and use two cables if you have two subs.

Final Thoughts

Match each cable to its job and its standard, buy certified where a standard applies, and spend extra only where length, rating or environment demands it. For how we judge claims, see How We Review.

About the author

BuyOnceChoice Editorial Team
BuyOnceChoice Editorial Team

The BuyOnceChoice Editorial Team researches durable products worth buying once. Our guides compare published specifications, warranty terms, expert review consensus, and verified owner feedback. We do not conduct our own product trials. See How We Review and our Editorial Policy for our standards.