Crossover Settings Explained: Large vs Small Speakers
Set speakers to Small, pick a crossover near the speaker real low end, and let the sub carry the rest. Leave auto setup alone unless it looks wrong.
Receiver crossover settings decide which low notes each speaker plays and which go to the subwoofer. A crossover is a frequency, usually 80 Hz, below which the receiver sends bass to the subwoofer instead of the speaker. Set most speakers to Small with an 80 Hz crossover, then raise it for compact speakers and lower it for large floorstanders.
What a crossover does
A crossover splits the audio signal at a chosen frequency. Everything above it goes to the speaker, and everything below it goes to the subwoofer. The point is to let each driver play the range it handles well. A small bookshelf speaker with a modest woofer strains and distorts on deep bass, and a subwoofer built for those notes plays them with less effort.
Your receiver does this split inside its bass management system. You choose a crossover frequency for each speaker group, and the receiver filters the signal accordingly. The speaker then plays a lighter, cleaner load, and the subwoofer handles the extra bass. This also frees the receiver’s amplifier from pushing deep bass into small drivers.
Crossover frequency is not a sharp wall. Filters roll off gradually, so the speaker and the subwoofer overlap around the chosen frequency. That overlap is the reason placement and phase matter, and the reason a crossover set a little too low or too high can leave a dip or a bump in the bass.
Large versus Small
Every receiver menu uses two labels, Large and Small, and they confuse almost everyone at first. They describe how the receiver treats the speaker, not how big the speaker is.
- Small: the receiver filters low bass from that speaker and sends it to the subwoofer. This is the right choice for nearly every speaker.
- Large: the receiver sends the full range signal to that speaker, with no bass management for it. Use this only when you have no subwoofer, or when you want a floorstanding speaker to play its own bass.
Some receivers offer Full Range or Off instead of Large. The meaning is the same. When a subwoofer is connected, many owners also set the front speakers to Small even when they are tall towers, because the subwoofer reproduces the lowest notes with less distortion and the receiver amplifier works less.
Choosing the crossover frequency
The standard starting point is 80 Hz, a value widely used in home theater standards and in automatic setup systems. It works for a broad range of speakers. From there, adjust by speaker size and capability.
| Speaker type | Starting crossover | Why |
|---|---|---|
| Small satellite or compact bookshelf | 100 to 120 Hz | The small woofer cannot play deep bass cleanly |
| Typical bookshelf | 80 Hz | A balanced starting point |
| Larger bookshelf or floorstander | 60 to 80 Hz | The speaker can reach lower, so give it more range |
| Ceiling and wall speakers | 100 to 120 Hz | Usually small drivers with limited bass |
| Center channel | 80 to 100 Hz | Often a smaller driver than the fronts |
Check the speaker’s published frequency response in the manual. A rule of thumb is to set the crossover at least a little above the lowest frequency the speaker plays comfortably, since a speaker usually rolls off near its stated low limit. If the manual states a low limit of 60 Hz, a crossover of 80 Hz leaves some margin.
Use one crossover for all speakers if you want simplicity, and match it to the weakest speaker in the system. The center and surround speakers are commonly the smallest. A single higher value, such as 100 Hz, keeps all of them out of their strain range.
The LFE channel and sub settings
Movie soundtracks carry a separate channel for low frequency effects, called LFE. It is the “.1” in 5.1. The receiver sends this channel to the subwoofer regardless of your crossover choices. The crossover affects bass in the other channels, which gets redirected to the sub as well when speakers are set to Small.
On the subwoofer itself, you may see a crossover dial or a low pass filter switch. When the receiver handles bass management, set the subwoofer’s own crossover to its highest value, or to the LFE or bypass position if it has one. Otherwise two filters stack, and bass loses output near the handoff frequency. Read the subwoofer manual, because the correct position differs by model.
Many receivers also offer an LFE low pass setting, with a typical value of 120 Hz. Leave it at the default unless the manual advises otherwise.
When to leave auto setup alone
Most receivers include an automatic setup, which uses a supplied microphone to measure speaker distance, level and size, then sets a crossover. It is a useful starting point, and in many rooms it is close to what you would choose by hand.
Leave auto setup alone when:
- It sets every speaker to a sensible value between 60 and 120 Hz and the sound is balanced.
- You do not hear a gap or boom in the bass.
- The distance and level readings match what you would expect from your seating.
Adjust by hand when auto setup picks an odd value, such as a very low crossover for a tiny speaker, or when it labels a small speaker Large. Auto setup sometimes does this when the speaker plays low bass at the microphone position. Check the result in the receiver menu after the run and correct what looks wrong. Run the routine again after you move furniture or speakers.
Setting per speaker
Work through the speaker setup menu one group at a time: front left and right, center, surrounds, and any height speakers. Set each to Small, choose the crossover, then confirm the subwoofer is set to Yes or On.
Music and stereo listening
For two channel music, you have two reasonable options. One is to keep the same crossover as movies and let the subwoofer carry the bass. The other is to use a Pure Direct or Stereo mode that bypasses bass management, so the front speakers play full range. If your front speakers are floorstanders with solid bass, the second option often sounds more natural for music. If they are small bookshelf speakers, keep the subwoofer engaged.
Common mistakes
- Setting Large for small speakers, which strains the drivers and leaves the subwoofer idle.
- Leaving the subwoofer’s own crossover at a low value while the receiver also filters, which thins the bass.
- Choosing a crossover so low that a gap opens between the speaker and the subwoofer.
- Setting each speaker to a different frequency without a reason, which makes the handoff harder to judge.
Who should adjust
Adjusting by hand helps most when you have mixed speakers, small ceiling speakers, or a room with awkward bass. A buyer with a matched speaker set and a good auto setup result can leave the defaults. If you are shopping, see our AV receivers category for models with detailed bass management, and the home theater speakers category for the speakers they will drive. Our How We Review page explains how we weigh these features.
Slopes, overlap and why the numbers are not exact
Crossovers have a slope, the rate at which the filter reduces output beyond the crossover point. It is commonly stated in decibels per octave. Steeper slopes separate the speaker and subwoofer more cleanly, but receivers fix the slope in their design and few let you change it. Because filters are gradual, a speaker set to 80 Hz still plays some content below that point, and the subwoofer still plays some above it. This is why two systems with the same number can sound different, and why you should trust your ears after the numbers get you close.
Subwoofer phase, distance and the handoff
The handoff sounds smooth only when the speaker and subwoofer arrive at your ears in step. Receivers handle this with distance settings and, on some, a subwoofer phase control. If bass sounds thin near the crossover, try flipping the subwoofer phase switch between 0 and 180 degrees, and keep the position that sounds fuller. Confirm that the receiver has the correct distance entered for the subwoofer.
Examples in words
A pair of compact bookshelf speakers with a small woofer, a center of similar size and four ceiling speakers would all be set to Small at 100 Hz. A pair of tall floorstanders with a modest center would put the fronts at 60 or 80 Hz and the center at 80 or 100. A system with no subwoofer sets the fronts to Large and runs without bass management. In each case, adjust by ear afterward.
Frequently Asked Questions
What crossover frequency should I use for my speakers?
Start at 80 Hz for most speakers. Use 100 to 120 Hz for small satellites and ceiling speakers, and 60 to 80 Hz for floorstanders. Check the speaker manual for its low frequency limit and set the crossover a little above it. Then adjust by ear until the bass blends smoothly between the speakers and the subwoofer.
Should my front speakers be Large or Small?
Small, in almost every system with a subwoofer. Small sends deep bass to the subwoofer, which reduces distortion and eases the load on the receiver. Large makes sense mainly when you have no subwoofer. Tall floorstanders can still be set to Small without losing their character, since they play everything above the crossover.
Do I set the crossover on the receiver or the subwoofer?
Set it on the receiver, and put the subwoofer’s own crossover at its highest value or its LFE or bypass setting. If both filters are active, they stack, and you lose bass near the handoff. Some subwoofers have no bypass, so check the manual for the recommended position when paired with a receiver.
Is automatic room correction accurate for crossover settings?
It is a good starting point, and often close. The routine measures what the microphone hears and picks a crossover and levels. It can misjudge when the microphone placement is poor or the room is noisy. Review the values afterward, correct anything odd, and listen to familiar music before you accept them.
Final Thoughts
Set your speakers to Small, start at 80 Hz, and move up for compact speakers or down for larger ones. Put the subwoofer’s own crossover out of the way, check the handoff by ear, and leave auto setup alone when it already sounds balanced. A few minutes in the menu gives cleaner bass and an easier load on the receiver.
Related buying guides
- Receiver HDMI Inputs: How Many Do You Need?
- Receiver Pre Outs Explained: Add an Amp Later
- Using a 7.1 Receiver With Fewer Speakers: Setup Guide