We independently review everything we recommend. When you buy through our links, we may earn a commission. Learn more›

Pressure Washer Winterizing and Pump Care

Water left in a pump can freeze and crack it. Drain the system, add pump saver, check the pump oil and stabilize fuel to protect the washer over winter.

To winterize a pressure washer, disconnect hoses, drain all water from the pump and wand, run a pump protector or antifreeze through the pump if the manual calls for it, check pump oil on models that have it, stabilize or drain fuel on gas units and store the machine in a dry place above freezing if you can. Freeze damage is the main risk.

Why freezing kills a pump

Water expands when it freezes, and a pump with water trapped in its chambers can crack the manifold, the valves or the pump head. The damage may not show until you try to use the washer in spring and find a leak or loss of pressure. Even a small amount of water left in the pump, hose or wand can cause damage in a hard freeze, and a washer stored in an unheated garage can see a hard freeze on a night when you least expect it.

Pumps are often the most expensive part of the machine, so winterizing is worth the effort. Storing the washer where it stays above freezing is the best protection, but protect the pump with the steps below even then, since water also corrodes parts.

Safety first

Fuel is flammable, so work outdoors with the engine off and cool, away from flames and sparks. Disconnect the spark plug wire on gas models before servicing, and unplug electric models. Do not use automotive antifreeze unless the manual says it is safe, because many pumps need a specific pump protector or a nontoxic RV antifreeze that is compatible with seals. Wear eye protection and gloves, since pump protector products are slippery and can irritate skin. Dispose of used liquids in accordance with local rules.

Draining the system

Turn off the machine and release the pressure by squeezing the trigger. Disconnect the garden hose and the high pressure hose from the pump, and drain them fully. Remove the wand and spray tip, and squeeze the trigger to drain the gun. For an electric washer, tip the machine as the manual allows to let water drain from the pump inlet and outlet. For a gas washer, pull the starter cord a few times with the spark plug wire disconnected, or follow the manual, to push residual water out of the pump.

Drain the detergent tank and rinse the siphon hose. Remove the inlet screen, check it and clean it. Leave all parts to dry indoors, and while you are at it, write down the model number and the pump type from the data plate, which helps when you order oil or seals in spring.

Pump protector or antifreeze

Many makers recommend running a pump saver product through the pump, which displaces water and adds lubrication and corrosion protection. Follow the product directions. Typically you connect the container, or pour the liquid into the inlet, and pull the trigger or crank the engine briefly until the liquid flows out the outlet. Use only products labeled for pressure washer pumps, or the type the manual lists, and avoid mixing different products.

Some owners use RV or marine antifreeze that is safe for plastics and seals, but only if the manual allows it, and not all pumps tolerate it. When in doubt, ask the maker or check the manual.

Pump oil and gas engine care

Axial and triplex pumps differ. Many triplex pumps have a crankcase that holds pump oil. Check its level and color. Milky oil means water has entered and the pump needs service. Change pump oil at the interval in the manual, using the type it names, which is often a nondetergent or pump specific oil rather than engine oil. Sealed axial pumps may have no oil to change.

For gas washers, treat the engine like any small engine. Add stabilizer to the fuel and run the engine briefly, or drain the tank and carburetor, change the engine oil, check the air filter and the spark plug and store the machine level. The same fuel logic applies as for a mower, which the lawn mowers category covers if you need a refresher on stabilizer versus draining. Keep fuel in an approved container away from the house.

Storage conditions and spring startup

Store the washer indoors, in a shed or a heated garage where possible, with hoses coiled loosely to avoid kinks and the wand stored with the tip removed. Cover it to keep out dust. Do not store the machine against a wall where moisture collects, and keep it off concrete floors that stay damp.

In spring, check for cracks, reconnect hoses, make sure the pump is full of water before starting, and run water through the pump for a minute before pulling the engine or pressing the power button, which prevents running dry. Check oil, fuel and the hose connections, and look for leaks before you use it.

A winterizing checklist

  • Release pressure, disconnect all hoses and drain the pump, gun and wand.
  • Treat the pump with a pump protector the manual allows.
  • Check and change pump oil if the model has it.
  • Stabilize or drain fuel, change engine oil, remove the spark plug wire.
  • Store dry, above freezing if possible, with a cover.

See the pressure washers category and How We Review for related reading.

Hoses, guns and fittings

Hoses fail at the ends and where they bend. Inspect the high pressure hose for bulges, kinks, cracks and leaking fittings, and replace it if it is damaged, since a failing hose under pressure is dangerous. Coil it without sharp bends and store it where it will not freeze. Check the O rings on quick connect fittings, since they dry and crack, and replace worn ones. Use a small dab of lubricant that the manual allows on the O rings to keep them supple. Inspect the trigger gun for leaks and smooth movement, and replace the garden hose inlet filter if it is clogged.

Common winter storage mistakes

  • Leaving the garden hose connected, which holds water against the pump.
  • Skipping the pump protector and storing in an unheated shed.
  • Using the wrong antifreeze or engine oil in the pump.
  • Leaving untreated fuel in the tank for months.
  • Storing the machine where rodents can chew hoses and wiring, or on bare damp concrete.
  • Forgetting to check pump oil for a milky color in spring.

If you discover that the washer froze with water in it, do not run it. Let it thaw indoors, check for cracks and leaks and call a service center before running the pump.

Costs of skipping the work

Maintenance records help here too. Note the date you drained the unit, the product you used and the oil you added, so you know what was done when spring arrives. A pump replacement can cost a large share of the machine’s price, while a bottle of pump protector and an hour of time costs little. The step that matters most is draining, and the second is keeping the washer from freezing. Even a few cold nights can cause damage if water remains.

A Fall to Spring Timeline

  1. First hard frost warning: drain, treat the pump, and bring the washer indoors, before the first freeze rather than after it.
  2. Same day: check pump oil on models that have it, and stabilize or drain fuel.
  3. Midwinter: look over the machine for rodent damage and moisture, and keep it off damp concrete.
  4. Early spring: check hoses, fittings, and oil, fill the pump with water before starting, and look for leaks.

Putting the first step on a calendar is the simplest way to avoid a cracked pump.

Frequently Asked Questions

How do I winterize a pressure washer?

Release pressure, disconnect and drain all hoses, the gun, and the wand, then drain the pump. Run a pump protector through it if the manual calls for one, check pump oil, stabilize or drain fuel on gas models, and store the washer in a dry place above freezing if you can.

Can a pressure washer freeze and break?

Yes. Water expands as it freezes and can crack the pump manifold, valves, or head, and the damage may not show until you use the washer in spring. Even a small amount of trapped water can cause damage in a hard freeze, so drain thoroughly and store it out of the cold.

Can I use antifreeze in my pressure washer pump?

Only if the manual allows it. Use products labeled for pressure washer pumps or the type the manual lists, since automotive antifreeze may not suit the seals. Some owners use RV antifreeze that is safe for plastics and seals, but not every pump tolerates it, so ask the maker when unsure.

What does milky pump oil mean?

Milky oil means water has entered the pump, and it needs service. Check the oil level and color on models with a crankcase, and change it at the interval in the manual with the type it names. Sealed pumps may have no oil to change. Do not run a pump with milky oil.

Final Thoughts

Freeze damage is the pump’s worst enemy, and prevention takes minutes. Drain the water, protect the pump with the product the maker allows, service the oil and fuel and store the machine somewhere dry. A little work in fall avoids a cracked pump in spring.

Related buying guides

About the author

BuyOnceChoice Editorial Team
BuyOnceChoice Editorial Team

The BuyOnceChoice Editorial Team researches durable products worth buying once. Our guides compare published specifications, warranty terms, expert review consensus, and verified owner feedback. We do not conduct our own product trials. See How We Review and our Editorial Policy for our standards.