Patio Heater Sizing: Watts and BTUs per Square Foot
Measure the zone you want warm, convert between watts and BTUs, derate for wind and open sides, and check that your circuit can carry an electric heater.
A patio heater size guide starts with the zone you want warm, not the whole patio: measure the seating area in square feet, convert the manufacturer’s heat rating to a single unit (one watt equals about 3.4 BTU per hour), compare it with the manufacturer’s stated coverage, and then derate for wind and open sides. An electric heater also needs a circuit that can carry its load, so check the wattage against the outlet or breaker.
Outdoor heating works differently from indoor heating, because heat escapes freely and wind carries it away. That is why no single watts-per-square-foot number applies everywhere. The method below lets you size from the manufacturer’s data and your own conditions.
Step one, define the zone
Decide where people sit or stand and measure only that area. A dining table for four needs a smaller zone than a lounge area for eight. Measure width and depth in feet, and multiply to get square feet. Note the ceiling or overhead height, since a low roof traps heat and a very high one lets it escape.
Also note how many sides are enclosed. A patio with a wall on one side and a roof is easier to heat than an open deck. Count walls, screens, windbreaks and the roof, and write them down, since you will use them in step three.
Mark the zone with chairs, a table or tape so that you can picture where the heater’s warmth must reach.
Step two, convert watts and BTUs
Electric heaters are rated in watts, and gas heaters in BTU per hour. To compare, multiply watts by 3.412 to get BTU per hour. A one and a half kilowatt electric heater is about five thousand one hundred BTU per hour, and a propane tower rated at forty thousand BTU per hour is nearly twelve kilowatts of fuel input.
Raw numbers do not compare directly, because the type of heat differs. Infrared electric heaters deliver heat to people more directly than air heating towers do, and gas heaters lose some energy as exhaust. Use the numbers to compare within a type, and rely on the manufacturer’s stated coverage across types.
Look for coverage data on the product page, such as a stated area or a radius. If it is not given, ask the maker or assume a small zone, and treat any number without conditions as a best case.
Step three, derate for wind and open sides
| Condition | Effect | What to do |
|---|---|---|
| Open on all sides | High heat loss | Choose a stronger heater or smaller zone |
| Wall on one side | Moderate loss | Place the heater near the wall |
| Roof overhead | Traps some heat | Check manual clearances first |
| Windy location | Heat blows away | Add windbreak, favor radiant types |
| Cold climate | Larger temperature gap | Size up or plan more heaters |
| Standing crowd | Larger zone | More coverage or several heaters |
Because stated coverage assumes mild conditions, derate it. If your patio is open and windy, assume the heater covers a much smaller zone than the specification suggests. A common approach is to halve the stated area for open, breezy spots and keep the full area for sheltered ones, then see whether one heater covers your zone or whether you need two.
Treat this as a conservative planning rule rather than a standard. If the heater will not comfortably cover your zone on a cool, calm evening, it will not do better in wind.
Mounting height and distance
Radiant heaters work best at a specific mounting height and distance from people, which the manual states. A heater mounted too high loses effect, and one mounted too low can be uncomfortable or hazardous. Follow the manual’s clearances to walls, ceilings, furniture and awnings.
For wall mounted units, plan the mounting point at the edge of the seating zone and aim the heater at people, not at the floor. Our wall mounted outdoor heater roundup shows how height changes coverage.
Free standing towers sit in the middle or at the edge of the zone, and the best position depends on the shape of the area.
Circuit and fuel checks
Electric heaters draw a lot of current. A one and a half kilowatt heater draws roughly twelve and a half amps on a standard household circuit, and a typical branch circuit has a limited capacity that is shared with other devices. Check the heater’s amps against the breaker and what else is on the circuit, and use an outdoor rated, ground fault protected outlet. Have a licensed electrician verify any hardwired install or circuit change.
Do not use extension cords unless the manual allows it, and then only those rated for the load and the outdoors. Do not overload a power strip.
For propane, check the tank size and the heater’s burn rate, and plan a safe location for the tank and a spare. Ensure ventilation and clearance as the manual describes.
Putting it together: an example
Suppose your seating zone is twelve feet by ten, which is one hundred twenty square feet, on a patio with a roof and one wall. The manufacturer says an electric infrared heater covers a certain area under mild conditions, and you derate it by about half because of the open sides. If the derated area is less than your zone, add a second heater, move the seating closer or choose a stronger model.
Then check the electrical load. Two heaters at the same circuit might exceed its capacity, so ask an electrician about a second circuit. Recheck the clearances for each heater, and place them so that warmth overlaps at the seats.
Think about the hours you will run the heater. A unit that warms a small zone for an hour before dinner has a different cost profile from one that runs all evening for guests. For long sessions, favor efficient placement and a windbreak over sheer power, because blocking the wind is cheaper than burning more fuel. A simple screen, a hedge or a curtain on the windward side can change the comfort of a patio more than a bigger heater.
Also consider the temperature range you want to cover. A heater that feels adequate on a cool autumn evening may feel weak on a freezing night, and the gap between air temperature and comfort grows as it gets colder. If you plan to use the patio into winter, size for the coldest evening you care about, not the average one.
Common Sizing Mistakes
- Measuring the whole patio. Heat the seats, not the empty corners, and measure only that zone.
- Trusting a coverage figure without conditions. A stated area usually assumes mild, calm weather.
- Comparing watts with BTUs directly. Convert first, then compare within a heater type.
- Forgetting the circuit. A strong heater that trips the breaker is no help, so check amps before you buy.
- Ignoring wind. A screen on the windward side can improve comfort more than extra power.
If you avoid these five, your sizing will be closer than most shoppers manage. Review the list again before you place an order, and again once the heater is set up, since real conditions on your patio are the final judge of whether the size was right.
Who should size up and who should skip
Size up if your patio is open and windy, you want to stand around the heater, or your climate is cold. Skip oversizing if your zone is small and covered, because extra heat is wasted and clearances become harder to meet. Skip heating the whole patio and heat the seats instead.
Write down your zone, your derated coverage and your circuit capacity before you shop. Those three numbers filter out most unsuitable heaters quickly.
Frequently Asked Questions
How many BTUs do I need for a patio heater?
There is no single number, because wind, open sides, and climate change how much heat reaches people. Measure your seating zone, compare it with the manufacturer’s stated coverage, then derate for open or windy conditions. One watt equals about 3.4 BTU per hour, so you can convert electric and gas ratings.
How many watts does a patio heater need to cover a seating area?
It depends on the heater type and conditions, so rely on the manufacturer’s stated coverage for your model rather than a watts per square foot rule. Infrared heaters deliver heat directly to people, so treat any coverage number as a best case, and derate for wind.
Can I plug an electric patio heater into any outdoor outlet?
Check the heater’s amperage against the circuit and everything else on it. A 1500 watt heater draws roughly 12.5 amps at household voltage. Use an outdoor rated, ground fault protected outlet, avoid extension cords unless the manual allows one, and ask a licensed electrician about hardwired installs.
Is one big heater better than two small ones?
For a larger or irregular zone, two smaller heaters can spread warmth more evenly and let people sit comfortably without crowding one hot spot. Check that each has the clearances the manual requires and that the circuit can carry both loads at the same time.
Final Thoughts
Size to the seating zone, convert units, derate for wind and open sides, and confirm the circuit or fuel supply. Use the manual for clearances, and a qualified professional for gas and hardwired electrical work. See How We Review for how we assess products, and the outdoor heaters category for models by type.
Related buying guides
- Propane vs Electric vs Infrared Patio Heater
- Wall Mounted vs Freestanding Patio Heater: Space, Wiring
- Patio Heater Safety: Clearance, Tip Over, Ventilation